EMAUX Salt Chlorinator

EMAUX SSC Series Salt Chlorinator

Crystal-clear water, sanitized automatically every day. No more adding chlorine by hand each week.

The cell installs on the return line after the filter, so every drop that passes through it picks up chlorine made from salt before flowing back to the pool. Soft water, no stinging eyes and no harsh chlorine smell. Ideal for home pools, villas and light-commercial pools up to 115 m³.

  • Self-cleaning cell: polarity reverses every 8 hours
  • Titanium plates resist corrosion
  • Automatic shut-off when there is no water flow
  • -T models have a built-in timer to run with the pump
15g/h
SSC15
Concrete pools up to 45 m³ / fiberglass 50 m³
25g/h
SSC25
Concrete pools up to 70 m³ / fiberglass 75 m³
45g/h
SSC50
Concrete pools up to 115 m³ / fiberglass 120 m³

EMAUX SSC Salt Chlorinator System in Operation

The pump draws water from the pool and sends it to the filter. Filtered water passes through the inlet valve into the salt cell, where electrolysis turns salt into chlorine, then leaves through the outlet valve and returns to the pool. The bypass valve lets you remove the cell for cleaning while filtration keeps running.

Salt chlorinator running Flow through cell: Normal System Control: 100% Operation lights 1 / 2: Green / Green
100 POWER OP1 OP2 SYS Control Box At least 3 mfrom pool water Mount≥ 1.5 mabovefloor Salt Cell Producing chlorine Cell cable Inlet valve Outlet valve Bypass valve Filtered water Pump to filter Wasteline Suction from pool Return to pool Sand Filter Pump

Swipe left or right to see the full diagram

Unfiltered pool water (orange dots) Filtered water (white dots) Chlorinated water returning to the pool Waste line (flows only during backwash) Cell cable
  1. 1DrawThe pump pulls pool water through its strainer basket
  2. 2FilterWater enters the sand filter via the multiport valve
  3. 3Into the cellOpen the inlet and outlet valves and partly close the bypass so water flows through the cell
  4. 4Make chlorineThe control box powers the cell, which converts salt into chlorine
  5. 5ReturnChlorinated water flows back to the pool for continuous sanitizing

EMAUX SSC Series Salt Chlorinator FAQ

30 frequently asked questions, from choosing a model, adding salt and daily settings to reading status lights, error codes and cleaning the cell. Pick a category below to see the answers.

EMAUX SSC Series at a Glance

Salt chlorinators for residential and light-commercial pools, with self-cleaning titanium cells (polarity reversal) and an IPX4 water-resistant control box.

SSC15

15g/h

  • Concrete poolup to 45 m³
  • Fiberglass / vinyl poolup to 50 m³
  • Cell power142 VA
  • Salt level3,000 – 4,000 ppm

SSC25

25g/h

  • Concrete poolup to 70 m³
  • Fiberglass / vinyl poolup to 75 m³
  • Cell power226 VA
  • Salt level3,000 – 4,000 ppm

SSC50

45g/h (actual)

  • Concrete poolup to 110 – 115 m³
  • Fiberglass / vinyl poolup to 120 m³
  • Cell power500 VA
  • Salt level4,000 – 5,000 ppm

The model suffix tells you the features

-ENo timer; must run together with the pump
-TBuilt-in timer plus a pump power outlet (up to 1.5 HP)
-TLTBuilt-in timer plus a 12 V transformer for pool lights

Power input 220–240 VAC 50/60 Hz. Connects to 1.5" or 2" pipe with the supplied unions. Not sure of your pool volume? See how to calculate it in the Sizing & Install tab.

Choosing a Model and Sizing

Calculate pool volume and daily chlorine demand, and install correctly per the manual.

Q1 – Q7
Q1How many SSC Series models are there, and how do they differ?

There are three output sizes: SSC15 (15 g/h), SSC25 (25 g/h) and SSC50 (45 g/h actual output). Each comes in three versions: -E (no timer; runs with the pump), -T (built-in timer plus a pump power outlet up to 1.5 HP) and -TLT (built-in timer plus a 12 V transformer for pool lights).

Q2How do I choose the right model for my pool size?

First calculate your pool volume in cubic metres (m³), then compare it with the model specs. Concrete pools use a slightly lower limit than fiberglass pools because concrete walls have a higher chlorine demand.

  • Up to 45 m³ → SSC15-E
  • 46 – 70 m³ → SSC25-E
  • 71 – 115 m³ → SSC50-E
Q3How do I calculate my pool volume?
Rectangular pool: width × length × average depth (m) = m³

Example: 5 × 10 × 1.5 = 75 m³. Round pool: 3.14 × radius² × average depth. For a freeform pool, split it into rectangles and circles and add them together (1 m³ = 1,000 litres).

Q4How do I calculate how much chlorine my pool needs per day?

The EMAUX manual uses a minimum of 2 mg of chlorine per litre (0.002 g/L).

Chlorine per day (g) = pool volume (litres) × 0.002

Example: a 65 m³ pool = 65,000 L × 0.002 = 130 g per day. An SSC15 (15 g/h) needs about 8.7 hours of production; an SSC25 (25 g/h) about 5.2 hours. In very hot weather or with heavy bather load, demand rises, so increase run time or add shock chlorine.

Q5My pool size falls between two models. Which should I choose?

Choose the larger model and set the System Control knob below 100%. The unit won't need to run at full power all the time, the cell works fewer hours, and you keep reserve capacity for hot spells or pool parties.

Q6Can I use it on a pool larger than 115 m³?

Yes, by installing several units so their combined output matches the pool volume. Cell positions and return-line splits must be designed so water flows evenly through every cell. We recommend having the WinWin Pool engineering team design the system.

Q7How do I install it correctly according to the manual?
  1. Mount the cell horizontally on the return line after the filter (and after the heater, if fitted) as the last device before water re-enters the pool. Follow the flow arrow on the cell.
  2. The cell must sit higher than the filter outlet. Install a bypass with inlet and outlet valves, but never close those valves while the unit is running.
  3. Place the control box at least 3.5 m from the pool edge, 1.5 m above the floor, no more than 4.5 m from the cell, with 50 cm of clearance, good ventilation, out of direct sunlight and away from acid or chemical storage.
  4. Supply power through a dedicated breaker and an RCD (residual current device) rated 30 mA or less, with proper earthing. Never use an extension strip.
  5. If the cell is below water level, the pump and chlorinator must share one switch so the unit never produces chlorine without water flow.
  6. After gluing pipe joints, wait 24 hours for them to cure before starting the system.
Mount the cell horizontally as the last device before water returns to the poolCell cable (control box within 4.5 m of the cell)From poolPumpFilterHeater (optional)Back to poolMain valveBypass: never close the inlet/outlet valves while runningInlet valveOutlet valveSalt cell (horizontal)SSC control box≥ 3.5 m from pool edge1.5 m above floorPower via 30 mA RCD
Salt cell installed on a bypass line

Water passes through the pump, filter and heater first, then into the salt cell on the bypass. To remove the cell for cleaning, switch off the chlorinator, then close the inlet and outlet valves. Filtration continues through the main valve.

Salt: Target Level and How Much to Add

Keeping the right salt level is the biggest factor in a long cell life.

Q8 – Q14
Q8What salt level should my pool have?

SSC15 and SSC25: 3,000 – 4,000 ppm. SSC50: 4,000 – 5,000 ppm. Do not exceed 5,000 ppm, or the unit will raise a high-salt warning and reduce chlorine output on its own.

Below 2,500 ppm the cell wears out quickly, and above 6,000 ppm stainless steel fittings in the pool may corrode.
Q9How many kilograms of salt do I add the first time?
Salt (kg) = pool volume (m³) × target salt level (ppm) ÷ 1,000

Easy rule: 1,000 ppm = 1 kg per 1 m³ of water.

Pool volume (m³)3,500 ppm (kg)4,000 ppm (kg)4,500 ppm (kg)
20708090
30105120135
45158180203
50175200225
70245280315
75263300338
100350400450
115403460518

We recommend targeting 3,500 ppm for SSC15/SSC25 and 4,500 ppm for SSC50 (mid-range). This table applies to fresh tap water with no salt yet.

Q10My salt reading is too low. How much should I add?
Salt to add (kg) = (target − measured) × pool volume (m³) ÷ 1,000

Example: a 50 m³ pool reads 2,800 ppm and you want 3,500 ppm → (3,500 − 2,800) × 50 ÷ 1,000 = 35 kg. Add it in stages, then re-test after 24 hours of circulation.

Q11What kind of salt can I use?

Use sodium chloride of 99% purity or higher (pool salt). Do not use:

  • Rock salt
  • Iodized salt
  • Salt with more than 1% anti-caking agent
  • Salt with more than 1% yellow prussiate of soda

Impurities in the salt shorten cell life.

Q12What is the correct way to add salt?
  1. Turn the chlorinator's System Control knob down to zero.
  2. Set the filter valve to Filtration or Recirculation and start the pump.
  3. Spread the salt around the pool. Don't leave it piled on the floor, and never pour large amounts near the skimmer.
  4. Run the filtration system for 24 hours, using the main drain as the main suction.
  5. Once the salt has fully dissolved, turn the knob back to its previous setting.
Q13Does the salt get used up? How often do I need to add more?

Salt isn't consumed when chlorine is produced, because chlorine turns back into salt after it sanitizes the water. Salt is lost through backwashing, splash-out, draining and dilution from rain. Test the salt level once a month, and after heavy rain or a large top-up of fresh water.

Q14I added too much salt. What should I do?

The only fix is to drain some water and refill with fresh water.

Share of water to drain = 1 − (target ÷ measured)

Example: reading 6,000 ppm, target 4,500 ppm → drain about 25% and refill. Meanwhile, the unit automatically reduces chlorine output to prevent overload.

Water Chemistry and Daily Operation

The chemistry you manage yourself, run times and the controls on the unit.

Q15 – Q21
Q15What water chemistry levels suit a salt chlorinator?

The chlorinator only produces chlorine; it does not balance your water. You need to test and adjust these levels yourself.

ParameterRecommended range
Free chlorine1.0 – 3.0 ppm
pH7.2 – 7.6
Cyanuric acid (stabilizer)30 – 50 ppm
Total alkalinity80 – 120 ppm
Calcium hardness200 – 400 ppm
Metals (copper, iron, etc.)0 ppm
Q16How many hours a day should the unit run?

The unit must always run together with the pump. Work out the hours from your daily chlorine demand (see Q4 in the Sizing tab), then adjust based on actual chlorine readings: below 1 ppm, add hours or raise the %; above 3 ppm, reduce. On -T models, set the timer so the pump and chlorinator switch on and off together.

Q17What do the display number and the System Control knob mean?

The System Control knob sets what share of each hour the cell produces chlorine.

  • 100 = produces continuously for the full 60 minutes
  • 50 = produces for 30 minutes, rests for 30 minutes
  • 30 = produces for 18 minutes, rests for 42 minutes
The System Control number sets chlorine production time in each hourGreen bar = cell producing chlorine / Dashed frame = rest period (pump keeps running)0 min15 min30 min45 min60 minProducing 60 minSet to 100Producing 30 minRest 30 minSet to 50Producing 18 minRest 42 minSet to 30
Operating cycle per hour by System Control setting

In normal operation, the number on the display is the chlorine output %. A green System Control light means the cell is producing; a red light means it is in a rest period.

Q18Do I need to switch off the chlorinator during backwash?
Yes, every time. Never let the unit run without water flowing through the cell. Gas builds up inside the cell housing, causing heat and pressure that can crack it.

After backwashing, set the valve back to Filtration before switching the chlorinator on again.

Q19In very hot weather or with many swimmers, chlorine runs short. What should I do?

The manual recommends increasing the unit's run time or adding shock chlorine (granular, tablet or liquid), which is safe to use alongside the salt chlorinator. Keep stabilizer at 30 – 50 ppm to reduce chlorine loss from sunlight.

Q20Why does pH rise easily in a salt pool?

Electrolysis of salt produces sodium hydroxide (NaOH) as a by-product, which pushes pH upward. Test pH at least once a week and add pH-reducing acid to keep it at 7.2 – 7.6. High pH makes chlorine less effective and causes scale to build up on the cell faster.

Q21What does the Winter Mode button do?

Winter Mode reduces chlorine output to 85% of the set level. Use it when the water is cold, which may trigger a red warning light. Most pools in Thailand rarely need it, except during cool spells in mountain areas.

Status Lights and Error Codes

Read the warning lights correctly before acting to avoid damaging the cell.

Q22 – Q27
Q22What do the Operation 1 and Operation 2 light colours mean?
OPERATION 1 and 2 lights show four unit statesGreen + Green: NormalOPERATION 1OPERATION 2Salt level OK, full chlorine outputNo action neededGreen + Red: Check the unitOPERATION 1OPERATION 2Low salt / scale on cell / cold waterTest salt first: add if low, clean the cell if normalRed + Green: Salt too highOPERATION 1OPERATION 2Output reduced to prevent overloadAbove 5,000 ppm, drain some waterRed + Red: Fix immediatelyOPERATION 1OPERATION 2Very low salt / heavy scale / very cold waterIgnoring it damages the cell and voids the warranty
OPERATION 1 / 2 lights: all 4 patterns
Operation 1Operation 2MeaningWhat to do
GreenGreenNormal operation, salt level OKNo action needed
GreenRedLow salt / scale on cell / cold waterTest salt; add if low, check and clean the cell if normal
RedGreenSalt too highTest salt; if above 5,000 ppm, drain some water
RedRedVery low salt / heavy scale / very cold waterStop the unit and fix it now, or the cell will be damaged
Q23Both lights are red. What should I do?

Don't pour in more salt straight away. Test the salt level with a meter or test strips first. If salt is low, add it as in Q10 in the Salt tab. If salt is normal but the lights stay red, scale on the titanium plates is the usual cause, so clean the cell as in Q28 in the Care tab. If gas output is still weak after cleaning, the cell may be at the end of its life. Contact WinWin Pool for an inspection.

Running the unit with low salt for long periods damages the cell and is not covered by the warranty.
Q24The No Flow light is on and the unit and pump have stopped. Why?

The No Flow light comes on when the water level inside the cell housing drops below the gas sensor. The system stops the pump and chlorinator automatically for safety. Check in this order:

  1. Is the pump running normally, sucking air, or is the pool water level below the skimmer?
  2. Is the filter valve stuck on Backwash, or is a bypass valve closed?
  3. Are there leaks at the pipes or the cell unions?
  4. Is the cell mounted horizontally and above the filter outlet? (Incorrect mounting traps gas in the cell.)
  5. Has the gas sensor cable come loose?
Q25What do error codes ER2, ER3 and ER4 mean?
CodeMeaningFix
ER2Terminal temperature too high (overheat protection)Switch off and let it cool, tighten the cell cable terminal nuts, then switch on again
ER3Temperature sensor disconnectedCheck that the sensor cable is not loose or unplugged
ER4AC input power faultCheck the transformer output wiring or a blown fuse

ER2 can be caused by very high salt, extreme heat or poor ventilation around the control box. Install the box under a sun shade or in a well-ventilated pump room.

Q26The display shows 888 or doesn't light up at all. What should I do?
Display stuck on 888 = internal fuse blown, replace the fuseNormal displayDIGITAL DISPLAYShows chlorine output % (100 = full power)Unit operating normallyStuck on 888DIGITAL DISPLAYInternal fuse blown, often from unstable powerUnplug, let it cool for 15 min, then replace the fuse
Normal display compared with a display showing 888

A display stuck on 888 means the internal fuse needs replacing, usually because of unstable power. We recommend fitting a breaker and a voltage stabilizer ahead of the unit. If the display doesn't light up at all, check the plug and power supply, the breaker, and that the cable between the control box and the cell is firmly connected at both ends.

Before opening the control box, unplug it and let it cool for at least 15 minutes.
Q27The unit is running but chlorine is low or zero. Why?
CauseFix
System Control set too lowRaise the % or turn it to maximum
Timer is cutting operationAdjust the timer settings (-T models)
Low saltAdd salt
Salt too highThe unit limits output; drain some water
Scale on the cellClean the cell
Blown fuseUnplug and replace the fuse
Cold waterTurn on Winter Mode
Low stabilizer / strong sun / high pHBalance the water as in Q15
No gas even after cleaningThe titanium plates may be worn out; replace the cell

Care, Cell Cleaning and Warranty

Correct care keeps the cell working longer and within warranty terms.

Q28 – Q30
Q28The cell is self-cleaning, so why clean it by hand, and how?

The unit reverses polarity every 8 hours to reduce scale, but hard water or high pH can still leave white limescale deposits. Inspect the titanium plates regularly and clean them when you see scale.

  1. Switch off the chlorinator and the filtration system, then unplug.
  2. Remove the cell from its housing.
  3. Mix hydrochloric (muriatic) acid with water at 1:10. Always add acid to water, never water to acid.
  4. Soak the cell for 5 – 10 minutes, keeping the electrical terminals out of the solution.
  5. Gently remove stubborn scale with a plastic tool. Never use sharp or metal objects.
  6. Rinse with clean water, refit and tighten, then restart the system as normal.
Wear gloves and eye protection and work in a well-ventilated area. For heavy scale, we recommend a salt cell cleaner, which is less corrosive than hydrochloric acid and can be used for soaks of up to 1 hour.
Q29How long does a cell last, and how do I know it needs replacing?

Cell life depends on operating hours, how well salt and water chemistry are maintained, and how often scale is cleaned. Running with low salt (below 2,500 ppm) wears the titanium coating fastest. Signs a cell is near the end of its life: little or no gas even after cleaning, and red lights that stay on even though the salt level is correct. WinWin Pool stocks genuine cells and spare parts for every SSC Series model.

Q30What does the warranty cover, and what is excluded?

The warranty covers defects in materials and workmanship under normal use, for the original purchaser buying through an authorized dealer. Consumable parts are excluded. The warranty does not apply in cases of:

  • Accidents, misuse or natural disasters
  • Use outside the conditions in the manual, such as running with low salt until the cell is damaged
  • Non-genuine parts or modifications to the unit
  • Repairs by anyone other than an authorized dealer

The warranty period is as stated on your WinWin Pool warranty card.

Can't find your answer, or need a technician to check your unit?

The WinWin Pool team can help you choose a model, calculate salt and service your EMAUX SSC Series, with genuine cells and spare parts for every model.

Sources: EMAUX SSC Series User Manual (EMSW25021112, 2025) and EMAUX Salt Chlorinator User Guide

SPAREPART

icon-messenger
This website uses cookies to enhance performance and provide you with a better user experience. You can read more details at: Privacy Policy and Cookies Policy